Hello,
I have started playing with vocore and I am coming here to find some answers
I have followed the starting tutorial with USB and the led in the boards turn on for a second when I connect the cable but it does not remains lighted and then the board heats up.
Is it a normal behaviour at starting? I haven't seen the vocore wifi but maybe I am not waiting the needed time.
Thanks
Noob - My Vocore is not starting [Solved]
- Neochange
- Posts: 7
- Joined: Fri Aug 28, 2015 9:30 am
Noob - My Vocore is not starting [Solved]
Last edited by Neochange on Sat Oct 10, 2015 2:40 pm, edited 1 time in total.
- Vonger
- Posts: 896
- Joined: Sun Oct 19, 2014 6:00 am
Re: Noob - Starting the Vocore
Hi, maybe there is something wrong when boot up, please connect VoCore with USB2TTL, check it log from computer, then we will know what is happening there.
- Neochange
- Posts: 7
- Joined: Fri Aug 28, 2015 9:30 am
Re: Noob - Starting the Vocore
I am going to test with a power supply instead of the usb cable and then I will use the TSB2TTL cable.
I hope I could find out what is happening...
Thanks!
I hope I could find out what is happening...
Thanks!
- Neochange
- Posts: 7
- Joined: Fri Aug 28, 2015 9:30 am
Re: Noob - Starting the Vocore
Vonger wrote:Hi, maybe there is something wrong when boot up, please connect VoCore with USB2TTL, check it log from computer, then we will know what is happening there.
I have attached the response I got through the USB2TTL cable. Should I reflash?
- Attachments
-
- VOCORE_log.png (18.59 KiB) Viewed 11874 times
- Vonger
- Posts: 896
- Joined: Sun Oct 19, 2014 6:00 am
Re: Noob - Starting the Vocore
Looks like the firmware is deleted, you can use uboot recover it, please read http://vocore.io/wiki/index/id:14 (uboot-kermit part)
- Neochange
- Posts: 7
- Joined: Fri Aug 28, 2015 9:30 am
Re: Noob - Starting the Vocore
Well I have downloaded a Vocore firmware from http://vonger.cn/upload/ ( the vocore.v1.0.bin )
and I am trying to upload the bin file to the board throught kermit. I open a terminal to the board and execute the command loadb as the tutorial says.
Then I use minicom to upload the file to the board with kermit. I tried to use kermit directly but if I press control-\ and the C nothing happens. When I try to upload the file everything seems OK but I got the error:
And this is the Kermit log while it is trying to upload the file:
After that, the error count raise and the communication interrupts.
and I am trying to upload the bin file to the board throught kermit. I open a terminal to the board and execute the command loadb as the tutorial says.
Then I use minicom to upload the file to the board with kermit. I tried to use kermit directly but if I press control-\ and the C nothing happens. When I try to upload the file everything seems OK but I got the error:
And this is the Kermit log while it is trying to upload the file:
After that, the error count raise and the communication interrupts.
- Vonger
- Posts: 896
- Joined: Sun Oct 19, 2014 6:00 am
Re: Noob - Starting the Vocore
The UART connection is not stable, so it failed, do you have a dock? so you can connect to ethernet and download by tftp.
- Neochange
- Posts: 7
- Joined: Fri Aug 28, 2015 9:30 am
Re: Noob - Starting the Vocore
Vonger wrote:The UART connection is not stable, so it failed, do you have a dock? so you can connect to ethernet and download by tftp.
I solved!
The uart connection was not stable because I "forgot" ( not really forgot, i didn't know it) to connect the ground cable to the board through the UART port. Log session looked good but when I tried to upload the file, it was failing all times. With the GND cable connected the transmission was OK and I could upload the binary.
I have learned more with these errors than if the board was correctly setup XD
thanks for your patience
8 posts
Page 1 of 1
Who is online
Users browsing this forum: Google [Bot] and 68 guests