just wondering whether someone tried to make a new openwrt image and load it onto VoCore? I want to include gpio-keys kernel module - someone got experience to share? Vonger, can you perhaps give a brief howto how to do it?
Rgds,
Jonas
Anyone had done a new openwrt-image yet?
- Greenwire-Elektronik
- Posts: 101
- Joined: Thu Dec 04, 2014 6:31 am
- darksoul
- Posts: 45
- Joined: Fri Nov 14, 2014 2:29 am
Re: Anyone had done a new openwrt-image yet?
http://o-ak.com/blog/o-ak-tech/openwrt- ... asy-steps/
Step by Step, all tested, all works!
The guide is universal, at the bottom you will find what you need to change for vocode firmware.
Step by Step, all tested, all works!
The guide is universal, at the bottom you will find what you need to change for vocode firmware.
- Greenwire-Elektronik
- Posts: 101
- Joined: Thu Dec 04, 2014 6:31 am
Re: Anyone had done a new openwrt-image yet?
darksoul wrote:Just did 15 minutes ago.
Do you want me to write a step-by-step guide?
Sure! I tried to enter the patches i found on the blog but the patch failed finding the correct files. In fact i think a step-by-step-guide should be sticky so everyone can see it - you might consider a new topic for it
- Ripple
- Posts: 8
- Joined: Mon Dec 08, 2014 12:04 pm
Re: Anyone had done a new openwrt-image yet?
Just a quick question. If I want to install a newer version of OpenWRT on VoCore, what's the correct way to do it? Does OpenWRT website offer a pre-built image for this device like it does for many routers? Is there an Image Builder? Or do I have to cross compile everything myself from source?
Best regards!
Best regards!
- darksoul
- Posts: 45
- Joined: Fri Nov 14, 2014 2:29 am
Re: Anyone had done a new openwrt-image yet?
Get the latest fresh image here - https://downloads.openwrt.org/snapshots/trunk/ramips/openwrt-ramips-rt305x-vocore-squashfs-sysupgrade.bin
there are two ways to upgrade, via terminal or luci.
check out the link that i gave earlier there is an example.
there are two ways to upgrade, via terminal or luci.
check out the link that i gave earlier there is an example.
- Greenwire-Elektronik
- Posts: 101
- Joined: Thu Dec 04, 2014 6:31 am
Re: Anyone had done a new openwrt-image yet?
darksoul wrote:Get the latest fresh image here - https://downloads.openwrt.org/snapshots/trunk/ramips/openwrt-ramips-rt305x-vocore-squashfs-sysupgrade.bin
there are two ways to upgrade, via terminal or luci.
check out the link that i gave earlier there is an example.
Thanks!
- earlaker
- Posts: 1
- Joined: Thu Dec 11, 2014 5:46 am
Re: Anyone had done a new openwrt-image yet?
That image will brick your VoCore. Trust me, I just did it
- charliex
- Posts: 42
- Joined: Sun Nov 16, 2014 5:34 pm
- Location: los angeles
Re: Anyone had done a new openwrt-image yet?
did it brick it, or just turn off the wifi ? ive used the prebuilt before
-
pcnate - Posts: 3
- Joined: Sat Dec 06, 2014 1:35 am
- Location: Wisconsin USA
Re: Anyone had done a new openwrt-image yet?
I installed the image using the web interface using the save config option. It booted fine for me. Only issue is no web interface afterwards, which doesn't bother me as I am uninterested in a web server on anything with less than 100MB ram. I always have the serial connection open anyways.
- fmotta
- Posts: 1
- Joined: Tue Dec 08, 2015 8:34 pm
Re: Anyone had done a new openwrt-image yet?
I have built about 20 different images with differing features.
Other than a likelihood that I will have to recover a board (speculatively) because I made the image too large it works great as documented.
Other than a likelihood that I will have to recover a board (speculatively) because I made the image too large it works great as documented.
10 posts
Page 1 of 1
Who is online
Users browsing this forum: No registered users and 10 guests